SAFY9 Hardwire Kit Web Manual

Dashcam Hardwire Kit – Quick Start Guide (Text-only, TOC + Content)

Dashcam Hardwire Kit – Quick Start Guide

Important safety information

Danger

Failure to observe the following directions could result in death or property damage.

  • Do not disassemble, repair, or modify the product yourself. Doing so may cause fire, electric shock, or malfunction. For internal inspection and repair, contact the service center.
  • Contact the service center for repair.
  • Do not adjust the product while driving. Doing so may cause an accident. Stop or park your car in a safe place before installing and setting up the product.
  • Do not install the product in a location where the product can obstruct the driver's field of vision. Doing so may cause an accident.
  • Do not use a damaged or modified power cord. Only use the cords provided by the manufacturer. Damaged or modified power cords may cause an explosion, fire, or malfunction.
  • Do not operate the product with wet hands. Doing so may cause electric shock.
  • Do not install the product in an environment with high humidity, or combustible gases or liquids.

Warning

Failure to observe the following directions could result in death or serious injury.

  • Do not leave the product near infants, children, or pets. There is a risk of them swallowing small components, and/or their saliva may get into the product, causing an explosion due to a short circuit.
  • Do not spray water or wax directly onto the product while cleaning the inside of the car. Doing so may cause fire, electric shock, or malfunction.
  • If smoke or an unusual smell is emitted from the power cord, detach the power cord immediately. Contact the service center or your distributor.
  • Keep the terminals of the power cord clean. Failure to do so may cause excessive heat and fire.
  • Use the correct input voltage. Failure to do so may cause explosion, fire, or malfunction.
  • Plug in the power cord firmly so that it cannot easily be disconnected. Failure to do so may cause fire.
  • Do not cover the product with any material. Doing so may cause external deformation of the product or fire. Use the product and peripherals in a well‑ventilated location.

In the box

Please check all included items before use to ensure nothing is missing or damaged.


  • Hardwiring Power Cable (3.5 m)
  • Quick start guide
  • Micro2 Fuse Holder & 5A Fuse (2 sets)
  • ATO Fuse Holder & 5A Fuse (2 sets)
  • Mini Fuse Holder & 5A Fuse (2 sets)
  • LPM Fuse Holder & 5A Fuse (2 sets)

Installation – Hardwire Kit

Step 1. Locate the Fuse Box

  • In most vehicles, the fuse box is located under the driver’s side dashboard, near the steering column, or inside the glove compartment.
  • Refer to your vehicle’s user manual to find the exact location. “Typical Fuse Box Locations in Passenger Vehicles”.

Step 2. Identify the Fuse Type and Select the Correct Holder

  • Fuse types vary by vehicle. Remove one of the existing fuses and compare it with the supplied fuse holders.
  • Supported types: Micro2 / ATO / ATO (??) / LPM. (The manual shows Micro2, Mini, ATO, and LPM.)
  • Use the fuse holder that matches the shape and size of the original fuse. “Match the fuse type by shape and pin spacing”.

Step 3. Connect the Hardwire Power Cable

Wire Functions

  • ACC(+), Yellow – Connects to a fuse slot that receives power only when the ignition is ON.
  • VCC(+), Red – Connects to a fuse slot that receives constant power, regardless of ignition status.
  • GND(-), Black – Connects to a clean, unpainted metal bolt on the vehicle chassis for grounding.

Connecting the Fuse Tap to the Hardwire Cable

  • Each ACC and VCC wire is pre‑configured with a plug‑and‑play fuse tap connector — no crimping tool is required.
  • Simply select the fuse tap type that matches your vehicle’s fuse slot (Micro2, Mini, ATO, or LPM) and plug the corresponding fuse tap onto the selected wire (ACC and VCC).
  • Ensure the connection is firm and fully inserted.
  • Tip: Do not connect both wires to a single fuse tap. ACC and VCC must be installed in separate fuse slots.

Identifying ACC and VCC Fuse Slots

  • Use a multimeter or test light to check the voltage at each slot:
  • ACC: 0V when the ignition is OFF; 12V+ when ON.
  • VCC: 12V+ at all times, regardless of ignition.
  • Common labels for ACC fuses: ACC, IGN, Radio, Audio, Power Outlet.
  • Common labels for VCC fuses: Dome, Clock, ECU, Memory, Hazard.
  • Tip: Refer to your vehicle’s fuse box diagram, located on the fuse panel cover or in the owner’s manual.

Inserting Fuses into the Fuse Tap

  • Each fuse tap is pre‑installed with a 5A fuse to protect the dashcam circuit.
  • Into the empty slot of the fuse tap, insert the original fuse removed from your vehicle.
  • This allows the factory circuit to continue functioning normally, while also powering the dashcam.

  • Make sure both fuses are fully seated and the fuse tap blades are securely inserted into the fuse slot.

Inserting the Fuse Tap into the Vehicle’s Fuse Box

  • Insert the fuse tap labeled ACC (Yellow wire) into the fuse slot identified as switched power (ACC). This slot only receives power when the ignition is turned ON.
  • Insert the fuse tap labeled VCC (Red wire) into the fuse slot identified as constant power (VCC). This slot should supply 12V at all times, regardless of ignition status.
  • Press each fuse tap firmly and fully into the corresponding slot in the fuse box.
  • You should feel a slight resistance and then a secure fit as the blades seat properly.

Ground Wire Connection

  • Attach the GND (black) wire’s ring terminal to a metal bolt on the vehicle chassis.
  • Ensure the bolt is clean, unpainted, and free of rust or insulation for proper grounding.
  • Tighten the connection securely.

Step 4. Connect to Dashcam and Verify

  • Plug the hardwire cable into the dashcam’s power port (DC‑in).
  • Start the engine to check if the dashcam powers on normally.
  • Turn the ignition OFF to verify that the dashcam remains powered — this indicates Parking Mode is working correctly.

Step 5. Tidy Up the Cables and Finish

  • Neatly route and secure the power cable along the headliner, A‑pillar, and under the dashboard.
  • Use the included tool or cable ties to keep the cable hidden and away from moving parts or airbags.
  • Once cable management is complete, your dashcam installation is finished.
  • The dashcam will power on during driving and automatically switch to Parking Mode when the ignition is off.

Product / Support

Product: Dashcam Hardwire Kit
Model Name: HWK‑SAFY
Manufactured for: Pittasoft Co., Ltd.
Address: 4F ABN Tower, 331, Pangyo‑ro, Bundang‑gu, Seongnam‑si, Gyeonggi‑do, Republic of Korea, 13488
Customer Support: cs@safydirect.com
Warranty: One‑year Limited Warranty


instagram.com/Safydirect_Official
youtube.com/Safydirect_Official
www.safydirect.com